Additives
The oil must fulfill its function in the presence of contaminants such as water, dust, combustion products and other chemical reactions. Much of large particles caught in it are trapped in the oil filter, but the smaller ones remain in the oil, gradually deteriorate its quality, and become a wear prerequisite as well as one of the reasons for its replacement.
Additives in oils have an important role in ensuring the stability under high temperatures, counteract the pollution of water, fuel and harmful acidic combustion products. They include metallic and polymeric dispersants (from disperce - dissipate, scatter), anti-corrosive and anti-oxidant, anti-wear and anti-seizure compounds, viscosity improvers and additives prevents formation of crystals at low temperatures, demulsifying and antifoam components. Additives are expensive substances with a specific purpose, which are added in precise quantity in order to achieve a balance - even small deviations can significantly alter the oil performance. Quantities and rates are determined by the manufacturers after intensive laboratory experiments and torque engine tests. The exact type and quantity of the substances that form the additives are known only to the manufacturers, so there is no case in which oil companies recommend or admire use of additional additives. Contrary to that, they believe that it infringes the said balance of ingredients and carefully crafted eventually may experience adverse chemical reactions and compounds.

Therefore, each class of oil differs with different characteristics in the main parameters that must meet (see attached table):
For comparison we have taken ACEA A3/B4-08 and VW 507.00. As it can be seen VW class covers a lot more key features. Considering the higher requirements for engines using VW 507.00 class, there are used new comparing to ACEA A3/B4-08 additives (This class has already covered such requirements for fuel economy) and better results in the other parameters.
In order to prevent the friction metal in metal where it is possible this to happen for a while, using compounds of zinc in combination with phosphorus - they form a thin boundary layer which allows even briefly forced friction parts without disastrous consequences. Their action is based on the chemical interaction of the products of their decomposition with rubbing metal surfaces. Anti-wear additives does not function fully when the engine is cold, which is one of the main reasons for the extremely intensive engine wear at cold start. Furthermore, over time the additives lose their properties, which is also one of the main reasons for the need of an oil change.
The abrasion wearing, caused by the presence in the oil of different solids and oxidation products is avoided by filters usage, while the action of the smaller particles is eliminated by anti-wear modifiers. The danger comes mainly from the possibility of particles to start sticking which will lead to increasing of their size, which process actually forms derive sludge, varnish deposits and soot. So-called detergent (cleaning) and dispersants (homogenizers) are in the oil to "neutralize" these particles, allowing them to move freely in the oil. The additives molecules are composed of two main parts - the long hydrocarbon tails and polar heads. Tails supports dissolving dispersants in the oil, and the polar head attach the particles pollutants.
Another essential task of motor oil is to reduce forming of the sludge and prevention of corrosive processes. Corrosive wear is caused by acidic combustion products, resins, and other compounds that flow over piston rings, and special additives task is to neutralize them. Elimination of the lead in gasoline octane and reducing sulfur levels greatly facilitate the work of oils, but their stability remains a key issue. That issue is mostly determined by the susceptibility to oxidation, which is generally countered by anti-corrosion additives that destroy chains free radicals and peroxides, participating in the oxidation process.
Chemists solve the problems with conflicting requirements of lubrication conditions at high and low temperatures with the addition of viscosity enhancers - polymers with long molecular chains and a molecular weight between 10 000 and 1 million. These molecules have the ability to "swell" with temperature increasing, which swelling leads to keeping of oil viscosity at a sufficiently high level in high temperatures.
Together with these additives there are used also antifoaming additives, that prevent the oil of "bubbling" when the crankshaft and connecting rods splashes and scoop the oil from the crankcase. The presence of the air bubbles would significantly worsen the effective operation of lubrication system. Demulsification additives, help to expel accidentally entered into the system water.
As we said, creating the whole complex of substances is a very difficult process and involves a lot of theoretical and practical work, which requires multiple laboratory and dynamometer tests.
The biggest challenge for engineers in recent years is the need to create oils which additives do not contaminate the new filters for nitrogen oxides and DPF (diesel particulate filter). Since some additives contain substances, including compounds of metals , sulfur ( present in the composition of antioxidants, in anti-wear additive, in detergents and base oils) , phosphorus (in anti-wear additives) and a sulfate ash (that is, salts of sulfuric acid, in this case of calcium phosphate and sulphate sulfur contained in the anti-wear modifiers) are contraindicated for DeNOx catalysts , three-way catalysts and particulate filters. These substances clog them, so substitutes of them should be invented. That leads of creating oils in which these substances are with low consistent, andf these products take name Medium and Low SAPs (from British Sulphur, Ash, Phosphorus). This is the new generation of oils. According to the creators of these oils these products are the result of the drastic changes of the molecular architecture of the oils in the resent years. In these oils there are used modified additives which should be used only in countries which offer low-sulfur content fuels, as these oils haven’t the ability to absorb large amounts of sulfur. Conventional oils contain about 80% base oil, 4-6% viscosity modifier, and 12-14% additive package. The type of the first part and the package of second two, determines the quality of the oil. The additive package contain about 33% detergent (non-metallic component), about 55% of dispersant (based on metal), 10% anti-wear (based on metal), and about 2% of antioxidants (non-metallic).
Finally, let us summarize what are the most commonly used additives according to their application:
• Viscosity Index Improvers - these additives help the oil viscosity improve and preservation under normal and extreme operating conditions.
• Pour Point Depressants - These additives help the oil to remain liquid and easily to move into the engine at low temperatures also in winter.
• Anti-wear Additives - These additives help for formation of a thin and strong oil layer on all surfaces of moving parts. As a result, the parts are not placed directly to each other, and rub a film of oil in the oil layer. This reduces the friction, heat from friction and chafing.
• Detergents & Dispersants - These additives are responsible for the cleaning properties of the oil. Their function is to clean all dirt, and in the oil filter to be filtered mechanically, remaining in the filter.
• Oxidation Inhibitors - These additives help the oil to wear out more slowly, to prolong its life, do not allow the oil to oxidize.
• Corrosion & Rust Inhibitors - low quality petrol / diesel oils has condensation which causes rust and corrosion. These additives are intended to eliminate the development of rust and corrosion in the engine as a result the condensation in the engine.
• Defoamants - these additives help the oil to remain homogeneous and not foam during engine operation. The result is a steady flow of oil in the engine and homogeneous structure of the oil during exploitation.
• Additives for catalytic converters - these grafts are only found in synthetic oils. They not only make it so that the oil does not interfere with the performance of the catalyst, but also help spare the catalyst. And that's reduced emissions.
